Find Jobs
Hire Freelancers

Circuit Board Design

$250-750 USD

Closed
Posted about 7 years ago

$250-750 USD

Paid on delivery
I am developing a new electronic puzzle. The puzzle will consist of a 4 inch cubic box. Each face of the box will be a separate challenge. Face #1: An LED and 9 Push buttons are mounted on this face in a 3x3 grid. When one is pressed, a single LED lights up. When pressure is released, the light goes off. In order to solve this face, all 9 buttons must be pressed simultaneously. When all are pressed at the same time, the LED goes on and stays on until all faces are solved (or the puzzle is reset). Face #2: This face has two screws and an LED. The LED is only illuminated when the two screw heads are linked by a paper clip (or other metal item). The LED stays on until all faces are solved (or the puzzle is reset). Face #3: This face has a small hole and and LED. A flashlight must be shined into the hole in order to illuminate the LED. The LED stays on until all faces are solved (or the puzzle is reset). Face #4: This side has a LED and a speaker sensor that detects loud noises. The player must shout near the speaker in order to illuminate the LED. The LED stays on until all faces are solved (or the puzzle is reset). Face #5: This face has a LED and a magnetic sensor. The user must place a magnet near the face in order to illuminate the LED. The LED stays on until all faces are solved (or the puzzle is reset). Face #6: This face doesn't have an LED. The surface is perfectly flat. The final challenge is to trip an accelerometer switch by spinning the box on a table. This activates the last switch for 2 minutes. When all sides are solved (all LEDs illuminated and accelerometer switch is activated), there is a buzzing sound from an internal speaker and all of the LEDs flash 10 times simultaneously. The puzzle is then reset and all LEDs shut off. I would like it to run on a single AA, or single AAA, or single 9V battery if possible. Each LED and switch automatically goes off after 2 minutes of being on...this is the reset function. Therefore, the puzzle must be solved in less than 2 minutes. I believe these are all very simple switch circuits. I need a design that is ready to order from a circuit board manufacturer and easy to finish assembly within the box myself. I will need some instruction on parts to order and where to solder wires. The circuit board will be glued to the inside of the box.
Project ID: 12703859

About the project

28 proposals
Remote project
Active 7 yrs ago

Looking to make some money?

Benefits of bidding on Freelancer

Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
28 freelancers are bidding on average $519 USD for this job
User Avatar
Hi I am an expert electronics engineer with more than 8 years of experience The idea seems interesting I would like to work on it, Please have a look at my profile to see my reputation and do let me know if you are interested in working with me Regards
$600 USD in 10 days
4.8 (250 reviews)
7.9
7.9
User Avatar
Hello dear I have experience in designing electronics circuits and can make your project. I will make your project practically on breadboard and will provide you circuit, code and PCB design. I can also develop android and windows based apps that can control the hardware. I will design your project using extra cheap components that will be beneficial for you if you are planning to make a commercial product. If you wish we can discuss in chat.
$700 USD in 15 days
4.8 (69 reviews)
7.1
7.1
User Avatar
Hi, i hope you are doing well. I have experience in LED based embedded project design and development. I have understood your project requirements and I can execute it in less possible time. Looking Forward, Khawaja
$526 USD in 10 days
4.9 (48 reviews)
6.8
6.8
User Avatar
Hi I am interested to your project. I am familiar with electronics, PIC microcotroller as well as PCB design by Eagle. Thanks.
$444 USD in 20 days
4.9 (95 reviews)
6.4
6.4
User Avatar
Hello Sir/Madam, I am Anthony Perera from Sri Lanka and I have multiple degrees on Engineering field. Why you should hire me ? * I am a FULL TIME freelancer and once a project is awarded to me,all my time will be dedicated to that specific project so you will get fast and quality work. * I have been in the field of product designing so if you are developing a commercial device I can help you to design it at very low cost and also can get into contact with Chinese manufacturers who I work with. Very reliable and fast. * I have my own PCB printing facility and also a workshop where I can design and manufacture any number of samples/prototypes. In that way you don't have to find some one else to test my work. * My prices are very fair and can be negotiated all the time. I am very flexible and very understanding. You can see my reviews. Check my profile. See for your self. https://www.freelancer.com/u/Anthony989.html Thank you Anthony Perera
$555 USD in 10 days
4.8 (62 reviews)
6.5
6.5
User Avatar
Hello I have got your job posting “Circuit Board Design” and I am very much interested to work in your project. I am a circuit designer and have more than 5 years experience of working with the embedded systems(Arduino,Rasberry pi ,ARM processors ,PIC microcontrollers,Wireless boards,TFT Touch Displays,All types of sensors and actuators). i have done tons of similar projects So, I think you’ll find, I have the skills you’re looking for. For more on my skills and successfully finished projects, please have a look on my Profile and Portfolio. I have all the components available here with me so i will develop a working prototype according to your specifications and then send you the code, schematics and board design so things will work for sure.I will remotely guide you and help you build the system on your side.I also offer unlimited revisions of the code and you get timely updates of the project. I am always available on Email and Skype. Please have a voice or video chat if necessary. I will be available more than 60 hours per week and able to start your project as soon as possible according to you. Thank you for your consideration, Best Regards, Haseeb Shafqat
$300 USD in 7 days
4.9 (58 reviews)
6.2
6.2
User Avatar
Hi! I am Jordan, new one on Freelancer , a CE products and Disney & Marvel characters toys designer from China. I have 10 years of experiences in products design, molding and assembly. I have good knowledge of material, artwork and electronics and have good relationship with local design house and core components vendors. In past 2 years, i designed bluetooth anti-drop device and kid’s watch for european customer and baby thermometer for local company. I help my customers from product concept to mass production. I am interested in your project and confident that i could meet your requirements. More details could be discussed via my skype: YtterbyCreative! Tks!
$736 USD in 30 days
4.6 (7 reviews)
5.0
5.0
User Avatar
Hi. My bid includes circuit developing, pcb routing with 3D models. Manufacturing and soldering 2 boards. One board for me second for you. Also included EMS fast shipping to you. It is 60 days because I sent one device to end user. He test it and I implement his requirements. I suggest to use STM8L152 MCU. I prefer single PCB 10x10cm which is located on face #1. On this PCB are mounted all chips and 9 buttons with led. Another faces parts are connected by wires. If you want I also can use instead STM8 Bluetooth low energy chip NRF51822. Maybe you have ideas how to connect your cube to mofile phone. It allows to upgrade firmware over the air and change cube behavior. Best regards, Jura.
$777 USD in 60 days
5.0 (7 reviews)
4.2
4.2
User Avatar
Dear sir, I'm an electronics engineer with more than 4 years making product for customers around the world. As your project requirements, we can design 6 PCBs that match each Face specs. They will need buttons, reed-switch, gyroscope, sound level sensor and battery management circuit. I can help you design schematic, PCB layout and generate bill-of-matterials for manufacturing. Feel free to chat for further discussion!
$700 USD in 9 days
5.0 (8 reviews)
3.9
3.9
User Avatar
Hello, I am interested to work with you on this project. I have read the description and I can do this. Let me know if you are interested. Thanks. Chirag
$355 USD in 10 days
5.0 (7 reviews)
4.0
4.0
User Avatar
Hello, Finally someone on this website who give you a specification. (That's awesome) This is definitely something I'd like to undertake. Kind regards Jaymie
$750 USD in 15 days
5.0 (1 review)
3.8
3.8
User Avatar
Hi, We have 10 years of experience in Product development for Defense, Industrial projects. Micro-controllers we can work on PIC, STM32 and AVR and also we have all the development kit and instruments available with us. For PCB design we use KICAD v4. And all the components will be selected from Digikey or Mouser. Thanks and Regards, Santosh
$611 USD in 12 days
4.8 (5 reviews)
4.0
4.0
User Avatar
i am embedded design engineer with 17 years of experience in developing PCB layout and embedded firmware
$555 USD in 10 days
5.0 (5 reviews)
3.5
3.5
User Avatar
I am experienced researcher and lecturer of electronics subject. Also, I have a sound grip on LED concepts. I would like to work for your project.
$333 USD in 4 days
4.7 (2 reviews)
3.3
3.3
User Avatar
Don't worry, We are a professional and I work with Altium, Eagle PCB and Proteus. This circuit for project must has a Microcontroller. There are many Microcontroller. Which microcontroller do you prefer? We work with Microchip (PIC) and Arduino. We recommend Microchip for your project. Also the circuit need an accelerometer for Face #6 but this challenge can make with a physical design. Do you need ? Circuit Schematic ? Circuit simulation? PCB? Cube box Design? Contact us What software made the schematic? Our p a y p a l and e m a i l is alonsoborjadaza (at) g m a i l (d o t) c o m S K Y P E pin311
$388 USD in 20 days
5.0 (1 review)
1.1
1.1
User Avatar
Dear Employer, Hire me, I can do this project. Please reply me. I'll give you complete schematic ,PCB layout and well commented firmware of puzzle. I can start working on it immediately. I have experience in designing fastest finger first systems. waiting for your reply. please review my profile also. I am experienced electronics enthusiast. Please review my profile for details. Kindly reply if you have any question. My work area includes Computer Software, Embedded Systems (Hardware & Software), Analog & Digital Circuit design, PCB design services etc. My Capabilities: PCB & Schematic: Eagle, Altium Designer 15, Kicad, Proteus. Micrcontroller Arch.: 8051, AVR, PIC16/18/24/32, ARM7, ARM Cortex M0/M3,ESP,RFID,GSM/GPRS,Bluetooth etc. Programming Languages : C, C# .Net, VC++, PHP, ASP .Net etc. Programming tools & IDE: Keil-MDK, AVR Studio, MPLAB X, Visual Studio 2010/2012, Mikroelectronika Mcu Sillicon Vendors: NXP, Atmel, ST Microelectronics, Microchip etc. I am interested in this project. Kindly send me more details, so that I can proceed. Your work will kept only upto you. It'll not be use in any other place. I'll complete the job within time limit with professional quality. Currently I am running team of 10-12 people with excellent grip on various fields like circuit design, layout design, testing, firmware writing, computer software, system integration & many more.
$272 USD in 15 days
0.0 (1 review)
1.9
1.9
User Avatar
We are designing PCB in our company and we have very talented man power to full fill your requirement with quality and within certain period.
$444 USD in 10 days
0.0 (0 reviews)
0.0
0.0
User Avatar
Dear sir I am a new freelancer and Electric engineer that have many experience Give me a chance . if you want I can provide full working prototype too Sincerely Jin
$250 USD in 10 days
0.0 (0 reviews)
0.0
0.0
User Avatar
Dear Sir, We can complete the design of electronic puzzle so that you will be able to assemble it putting the least effort. Please message us to clarify any doubts if you have. Best Regards, Prasanth
$250 USD in 10 days
0.0 (0 reviews)
0.0
0.0
User Avatar
I believe these are all very simple switch circuits. I need a design that is ready to order from a circuit board manufacturer and easy to finish assembly within the box myself. I will need some instruction on parts to order and where to solder wires. The circuit board will be glued to the inside of the box
$500 USD in 10 days
0.0 (0 reviews)
0.0
0.0

About the client

Flag of UNITED STATES
Brooklyn, United States
5.0
6
Payment method verified
Member since Jun 11, 2014

Client Verification

Thanks! We’ve emailed you a link to claim your free credit.
Something went wrong while sending your email. Please try again.
Registered Users Total Jobs Posted
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Loading preview
Permission granted for Geolocation.
Your login session has expired and you have been logged out. Please log in again.