Design a 3D-printed casing for my PCB project. (STL-file only)

Completed Posted 2 years ago Paid on delivery
Completed Paid on delivery

This one is about a simple design for a small box holding some electronics (PCB) and a small lens. Right now, it’s a prototype, but it’s to be expected more proto's are needed before we're ready to finalize the end-model.

Kindly note: We need you to understand what we require BEFORE you make a bid on this job. Refer to the content of the description, so we’re sure you’ve read and understood it. Quotes without this reference are not entertained!

• We need an .STL-file for a square box with inner dimensions of 50 x 50 x 25 millimeters. Be aware of the 1-mm thickness of the 3D-printing material. The box should have rounded edges. You may design the outer dimensions up to 5-mm wider, however, the height only 2,5-mm.

Box is split in half. Top half 10 mm and bottom half 15 mm high. You may adjust this freely, as long as it serves its goal.

Both parts must be joined by solidly “clicking” them together. You need to advice me how this is achieved. It is mandatory to let the top half overlap the bottom half.

Between the two halves, a small rubber ring should be accommodated for, in order to keep moist out, once parts are clicked together.

The 12 mm part (top half) is holding the circuit board or PCB.

PCB is screwed to the top half, which should have three “pillars” with a 2-mm thread.

On the top half, there are two small opposite facing openings. One that is 3,5-mm wide and one that has the dimensions to allow for a micro-USB male connector.

The bottom half does not contain any other openings, other than one for a (camera)lens to protrude. This is a 7-mm hole at a defined location.

You’ll notice, I talk about top and bottom. The top half is connected (screwed) to the end-device in which it is used. And FYI, the lens is facing down from the bottom half. It records a technical process that takes place directly under need it. (After you have proven to be up for the job, you will be fully informed).

Now, once the upper and lower parts are joined, you have essentially a square box in your hands. It then needs to be connected to the said end-device. This is also done by a clicking mechanism. I have some ideas about that, but basically think of a square frame that is bolted/screwed to the end-device. The box snugly fits into the frame. The frame has two extending parts opposite of each other over the full length on both sides. These parts have a small hook over their full length that “click” in/on the overlapping top half (see above) and herewith solidly keep the box in place.

It is a very simple design, but I need you to be 100%-sure you’re able to make this. Please be honest and if you feel this is not your kind of work, do not accept the gig! When certain this can be done by you and you accept the job, you’ll also receive some photos of the PCB.

One remark. If you’re not able or willing to communicate and to discuss this job, do NOT reply! Only bidders who understand the need for effective communication are invited to bid.

Good luck!

3D Modelling 3D Design 3D CAD 3D Visualization

Project ID: #31591126

About the project

23 proposals Remote project Active 2 years ago

Awarded to:

charlemagne9

Hi, I believe I can create 3D printable models (stl) of the box casing according to your requirements (top hal, bottom half, click when closed, etc). I have experience in creating electronic casing before. I am using S More

$30 USD in 3 days
(57 Reviews)
5.4

23 freelancers are bidding on average $39 for this job

azraazeen9

Hello, i am ready exited to work you as i read your job description I am also an expert in making 2d,3d modelling and animating characters 2dautocad drawing ,elevation, solid work, Revit ,FBX ,Unity, Render also interi More

$125 USD in 3 days
(49 Reviews)
5.9
catdes

Hi, there. This is Kateryna, product designer with over 10 years of experience. I have checked your project details carefully and I was convinced that this project works best for me. I have many experiences working on More

$20 USD in 1 day
(17 Reviews)
5.3
glushkovvv

Dear I have read your description carefully. I am a solidworks expert. I have a lot of experiences in 3D modelling of case for PCB for 3D printing. You can confirm my skills in follow link: https://www.freelancer.com/ More

$20 USD in 1 day
(17 Reviews)
4.4
aspwriter

Hello, I have read the description and understand most of the project deliverables. There are just a few parts about the frame and fastening mechanisms that I will need additional information on which I hope we can man More

$80 USD in 7 days
(25 Reviews)
4.5
InstantCreate

Hi There, I would be a perfect fit for your project description of As professional experienced as Sr.2D/3D Artist. I have extensive experience in 3D Modeling, 3D Product Design, Logo 3D/2D Animation, 2D Explainer vide More

$20 USD in 7 days
(4 Reviews)
4.4
AndreyAgeenko

Hi, this is Andrey. I am a product designer. I have rich experience in 3d modeling, CAD/CAM and realistic rendering. Please check my portfolio. https://www.freelancer.com/u/AndreyAgeenko I can provide you good result More

$30 USD in 1 day
(7 Reviews)
3.2
abdulasalam94

Hello I am an expert in mechanical/automotive engineering, a specialist in product design. I have experienced with years of cad/cam, DFM, prototyping, product design, etc... I can create creative designs. Inbox me to More

$20 USD in 7 days
(4 Reviews)
2.0
valgonx

Hi there! I am an industrial designer from Argentina. Ive got a big experience on 3d modelling and realistic rendering. I´ve been using Rhinoceros and V-Ray for almost 10 years so I am able to model from simple to comp More

$30 USD in 1 day
(0 Reviews)
0.4
kn007

Hello, I saw your requirement for modelling a casing for pcb. I would like to share that right I am pursuing PhD in 3D printing. I am having 4 year experience of designing the parts for 3D printing. I am confident that More

$10 USD in 2 days
(0 Reviews)
0.0
Suryaprasanna7

Hi, This is My First project in this site. I can serve you immediately. Please give me a chance of the same.

$10 USD in 1 day
(0 Reviews)
0.0
sourabhk3553

Design & development engineer with 2+ years of experience in design of test fixtures & assembly line, process planning, new product development.

$25 USD in 7 days
(0 Reviews)
0.0