Electrical schematic drawing jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    9,245 electrical schematic drawing jobs found, pricing in GBP

    I need a USB boot-loader and C# Application GUI to update ATMEGA32U4 firmware It must be easy to use and install and has some...It must be easy to use and install and has some special requirements for the application. Please read the doc and tell me the WDT fuse requirements if you understand. Schematic to follow if you have read the doc properly

    £57 / hr (Avg Bid)
    £57 / hr Avg Bid
    18 bids

    A drum pad controller programmed for 21 piezo sensor pads and 1 FSR that will send...is built so I just need the micro controller and any other necessary components. It can either be a complete board or I could put it together with a list of components, a schematic and the code, but again it must be complete and tested with no errors in the code.

    £156 (Avg Bid)
    £156 Avg Bid
    11 bids

    I need someone that has experience with the TI ADS1248IPW IC and tell me what is wrong with my circuit. ...to fix it. Also need to be able to tell me how to configure the Registers to perform correct reading. I am connecting 4 2-wire PT1000 temperature sensors. I will provide Schematic picture in PM YOU MUST HAVE EXPERIENCE USING THE TI ADS1248IPW

    £62 (Avg Bid)
    £62 Avg Bid
    10 bids

    1st class work

    £141 - £422
    £141 - £422
    0 bids

    ...profile and would like to offer you my project. We can discuss any details over chat. I have a PCB file for Altium Designer, but the schematic was lost in a computer hard drive corruption. I am needing the schematic to be recreated from the PCB document. Can you do this task? We can adjust the quote from milestones if you are available. Thanks for

    £36 (Avg Bid)
    £36 Avg Bid
    1 bids
    Electrical Schematic Drawing 6 days left
    VERIFIED

    Dear Freelancer. I am seeking a freelancer to undertake a single page schematic drawing of a electrical drive instillation The drawing to be simple to understand which wire goes where with out the great detail as shown in the 3D attachment. Please Note: I am a bad communicator so heavy reliant on your expertise to get this project done.

    £73 (Avg Bid)
    £73 Avg Bid
    36 bids

    Task For the attached building design, to complete the following: 1. Complete electrical and plumbing design. Clearly illustrate drainage for emergency exit. 2. Design should incorporate two possible options for backup power - solar (on roof) and generator (basement or ground floor) - one design for each option. 3. Plumbing design should include

    £287 (Avg Bid)
    £287 Avg Bid
    18 bids

    Assembly of devices with mechanical and electrical connections

    £13 / hr (Avg Bid)
    £13 / hr Avg Bid
    25 bids

    Hello, I'm looking for an A/E to put together a permit submittal for my house design. I have a schematic design put together using Bluebeam software to get started. See Attached. It's a simple strait forward design with a gabled roof, slab on grade, and 9' ceilings. The lot is level. Submittal to include all required info for acceptance of permit

    £14 / hr (Avg Bid)
    Local
    £14 / hr Avg Bid
    9 bids

    I would like the Schematic for a PCB Camera. I have TFT LCD monitor and i want to attach the pcb camera to the monitor. So once i take a photo it appears on the monitor. This is a small project nothing special The budget is $100 Whole Project

    £65 (Avg Bid)
    £65 Avg Bid
    9 bids
    AutoCAD Electrical, 5 days left
    VERIFIED

    For this project I...has extensive experience in AutoCAD Electrical. The task is quite simple - I need to assign attributes to some wires or convert them into cables and assign attributes, then export these details to Excel or a textfile. It is very straightforward, but it is imperative that you have specifically used AutoCAD Electrical for many years

    £19 (Avg Bid)
    £19 Avg Bid
    29 bids

    I have 7 pages of electrical drawings which are my hand drawings need doing in auto cad can someone do these ASAP ???

    £214 (Avg Bid)
    £214 Avg Bid
    92 bids
    AutoCAD Electrical 5 days left
    VERIFIED

    For this project ...has extensive experience in AutoCAD Electrical. The task is quite simple - I need to assign attributes to some wires or convert them into cables and assign attributes, then export these details to Excel or a textfile. It is very straightforward, but it is imperative that you have specifically used AutoCAD Electrical for many years.

    £21 (Avg Bid)
    £21 Avg Bid
    13 bids

    For this project ...has extensive experience in AutoCAD Electrical. The task is quite simple - I need to assign attributes to some wires or convert them into cables and assign attributes, then export these details to Excel or a textfile. It is very straightforward, but it is imperative that you have specifically used AutoCAD Electrical for many years.

    £104 (Avg Bid)
    £104 Avg Bid
    11 bids

    i need someone with math and electrical

    £76 (Avg Bid)
    £76 Avg Bid
    40 bids
    Vortex Simple 3 days left

    ...and a prototype for a tube valve amplifier. - The tube valves should be contained in the PCB itself, connected by sockets. - The most important voltages are marked on the schematic for so that proper spacing and insulation are achieved. - The potentiometers and 1/4 Jacks will not be necessarily soldered directly to the board, so it is interesting to

    £55 (Avg Bid)
    £55 Avg Bid
    2 bids
    £18 Avg Bid
    27 bids
    £17 Avg Bid
    12 entries

    I need a chartered Electrical Engineer to help guide me through the chartered application process. Candidate must: 1) The candidate must present to me his/her Ceng certificate and registration number for varification. 2) Must have registered in the past 7 years. older registrants were following the old system and can not be of great help. 3) Must

    £22 (Avg Bid)
    £22 Avg Bid
    11 bids

    I have a very simple schematic (1 wire) and an Excel document with 4 different attributes for the wire (length, connector A type, connector B type and site. I want to first setup these wire attributes as default in AutoCAD Electrical and then import these attributes from the Excel document and assign them to the relevant wires automatically.

    £95 (Avg Bid)
    £95 Avg Bid
    10 bids